A Useful Mini-Guide on Fixing Your Dripping Faucet



Visit Site

Is your faucet dripping or dripping ? Drip, drip, drip! It's extremely easy to repair a leaky faucet by following this mini-guide.

Preparation Your Tools for Fixing

If you're a handyman, you could currently have the tools stowed away in your toolbox. Should you miss out on some tools, you can readily purchase these in any hardware store. You will require the following:
An adjustable c-wrench
Philips and flat-head screwdrivers
Replacement o-rings and washers
Penetrating oil like WD-40

Shut off Your Water Supply

Prior to you attempt to repair your leaking faucet, you must switch off that water system that feeds it fresh water. Ought to you forget to do this, you will experience a huge mess, deal with water damage, and clean-up. There's no need to touch the mainline so that other individuals can use the water in other parts of that home. You can typically discover the local valve in a close-by cabinet or under the sink. Normally, there are two valves, one for the cold and the other for the warm water supply. Turn them both off by turning the knob counterclockwise. Ascertain that water is cut by switching on the tap.

Take Out the Deal With Knob

As soon as all the water is cut, you can proceed with removing the decorative cap off the manage knob utilizing your flat head screwdriver. Once the cap is off, you will see a little screw that protects the handle to the stem of the faucet. Remove this screw with your Phillip's screwdriver so you can pry the manage from the stem.

Eliminate the Faucet Stem

Get your adjustable C-wrench for loosening up the packing nut. This will expose the stem. Depending upon your faucet configuration, the stem will easily pop out, or you will have to twist it off the valve. As soon as the stem is removed, check the parts for wear and tear.

Change the Rubber Rings

You should then replace the O-ring that sits around the middle part of the stem. From there, you must change the washer, which is commonly discovered in the bottom of the stem within the valve seat. It would be best to change both to make sure that the leaking stops.

Return the Faucet in Place

As soon as you have actually replaced the washer and O-ring, you must reassemble the faucet by following the reverse order of elimination. Withstand the urge to over-tighten anything so as not to strip the threads. Then, when it's back in place, test it out by turning on the water supply and faucet. If it still leakages, you could have a bigger issue like valve rust, broken, plumbing, or torn seals. In this case, calling a professional plumbing technician to do more complex repair work is in order.


Prior to you attempt to repair your dripping faucet, you should turn off that water supply that feeds it fresh water. As soon as the cap is off, you will see a small screw that secures the manage to the stem of the faucet. Depending on your faucet configuration, the stem will quickly pop out, or you will have to twist it off the valve. As soon as you've replaced the washer and O-ring, you need to reassemble the faucet by following the reverse order of elimination. When it's back in place, test it out by turning on the water supply and faucet.



Repairing A Leaky Faucet - Figuring Out Faucet Type


Drip, drip, drip. When you have a leaking faucet in your home, there are numerous troubles to be reckoned with. Of all, the sound can vary from a minor tapping in the background to a major barrier to sleep at night. You stand to lose some cash in terms of energy expenses, too, if the water you are losing is hot. If you live in an area where you pay for water use, you might end up with a large costs simply due to a leaking faucet- your leakage might lose you gallons of water every day, in the house repair equivalent of death by a thousand cuts.

There are several ways to fix your circumstance when you experience a leaking faucet, some of them band-aid services and some of them more long-term. One short-term service is to acquire a faucet washer- a little piece of metal that can screw on to the opening of your faucet to postpone the drip action. The water is still leaking, but the amount being lost is what is being dammed. This strategy does not work for very long, however, and can even be detrimental because it may make you forget that you really have to repair that leak sometime.

The more permanent solution. Naturally, is to discover the source of the drip and fix it. This is a relatively basic treatment that many people will be able to achieve on their own; if you utilize a plumbing professional for it you will be investing some huge bucks that you won't actually have to.

Composing and reading about repairing your dripping faucet is actually a more involved procedure than the actual doing, for the simple factor that prior to you can fix the issue you should identify what type of faucet you have. This will assist determine the treatment and the problem requirement to fix it.

There are four standard kinds of faucets- ball type, disc type, cartridge type, and compression type.

Compression type faucets are the earliest and most typical kinds of faucet, and can be identified in two steps. The initial step is visual- if your faucet has different handles for the cold and hot water, it is either a cartridge or compression faucet. You can identify which your faucet is either by feel or by taking the system apart and once again examining it visually. Compression faucet manages are meant to screw down and up in order to shut off or release the water flow- you have to add pressure in order to turn the tap off the whole way. A cartridge faucet does not require this included pressure, it simply swings quickly shut and the water circulation is cut off.

If you choose to make sure about your faucet type by taking the mechanism apart, first turn off your water. Compression faucets will have a shaft leading down into the body of the faucet.

The cartridge kind of faucet is washerless, as are the other 2 types, ball and disc. Ball types are operated by a single handle that swings backward and forward in between the hot and cold by a ball mechanism at the base of the faucet. Disc types have a single manage that extends outside towards the faucet and goes up and down to turn the water on and off, with a smooth horizontal pattern to change the levels of hot and cold water.

You will need to follow the correct treatments for fixing the drip according to the type of faucet you have identified when you have identified what kind of faucet you have.


One short-term option is to purchase a faucet washer- a little piece of metal that can screw on to the opening of your faucet to postpone the drip action. Compression type faucets are the oldest and most common types of faucet, and can be recognized in two actions. The very first step is visual- if your faucet has different manages for the cold and hot water, it is either a cartridge or compression faucet. Compression faucets will have a shaft leading down into the body of the faucet. The cartridge type of faucet is washerless, as are the other 2 types, ball and disc.

Leave a Reply

Your email address will not be published. Required fields are marked *